Sync dev to main

docs/products/rpro1/addons/add-the-ld2412-mmwave-sensor-to-r-pro-1.md

@@ -12,11 +12,11 @@ description: Tutorial on adding the LD2412 mmwave sensor to your R-PRO-1
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently remove the PCB from the case and flip it over.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Place the LD2412 on the 4 and 3 pin headers (only fits one way).
 

docs/products/rpro1/addons/adding-co2-to-r-pro-1.md

@@ -6,7 +6,7 @@ description: Tutorial on adding the SCD40 CO2 sensor to your R-Pro-1.
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. With the back removed, identify the bottom left corner where the small black mezzanine connector lives. You will see an "X" indicating which corner needs to be lined up with the SCD40 CO<sub>2</sub> sensor. There is an X on the SCD40 sensor's PCB as well, you can see it in the image below but it is slightly cut off on the PCB itself.
 

docs/products/rpro1/addons/attaching-gang-box-mount-to-r-pro-1.md

@@ -8,11 +8,11 @@ description: Tutorial on adding the gang box mounts to your R-Pro-1.
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently lift the PCB out of the case and set it face up with the USB-C port facing down.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Take the two gang box mount pieces and identify the one labeled "TOP" and the other piece which is the bottom mount.
 

docs/products/rpro1/addons/install-ceiling-mount-for-r-pro-1.md

@@ -4,15 +4,21 @@ description: Tutorial on installing the ceiling mount addon for the R-PRO-1.
 ---
 # Install Ceiling Mount for R-PRO-1
 
+Watch our step by step video on installing the R-PRO-1 using the Ceiling Mount. We have images showing how to assemble the mount below.
+
+<div class="cms-embed"><iframe width="560" height="315" src="https://www.youtube.com/embed/O4OZG3I34E4" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen=""></iframe></div>
+
 ###### Attaching Mounts
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)
+
+![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently lift the PCB out of the case and set it face up with the USB-C port facing down.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Take the two ceiling mount pieces and identify the one labeled "TOP" and the other piece which is the bottom mount.
 
@@ -22,36 +28,40 @@ description: Tutorial on installing the ceiling mount addon for the R-PRO-1.
 
 3\. Gently push the top mount labeled "TOP" into the pcb as shown below. Make sure the orientation is identical to the image below!
 
-![](/assets/r-pro-1-ceiling-box-top-mount.jpg)
+![](/assets/r-pro-1-ceiling-box-top-mount.webp)
 
 4\. Gently push the bottom mount into the pcb as shown below. Make sure the orientation is identical to the image below!
 
-![](/assets/r-pro-1-ceiling-box-bottom-mount.jpg)
+![](/assets/r-pro-1-ceiling-box-bottom-mount.webp)
 
 5\. The end result should look identical to the image below. You are now ready to install it inside of the ceiling mount.
 
-![](/assets/r-pro-1-ceiling-box-mounts-installed.jpg)
+![](/assets/r-pro-1-ceiling-box-mounts-installed.webp)
+
+###### Cut the Ceiling Hole
+
+The Ceiling Mount needs a 3.5 inch (around 89mm) circular hole in the ceiling. Cut that hole before you install the mount. A [2 in. to 7 in. adjustable hole saw](https://www.homedepot.com/p/Milwaukee-2-in-to-7-in-Black-Oxide-Adjustable-Hole-Saw-Cutter-49-56-0320/205744284) set to 3.5 inches is what we used.
 
 ###### Install in Ceiling Mount
 
 1\. Remove the cover to expose the inside of the installed Ceiling Mount.
 
-![](/assets/r-pro-1-ceiling-mount-cover-removed.jpg)
+![](/assets/r-pro-1-ceiling-mount-cover-removed.webp)
 
 2\. Plug in Ethernet cable or USB-C cable.
 
-![](/assets/r-pro-1-ceiling-mount-plug-in-eth.jpg)
+![](/assets/r-pro-1-ceiling-mount-plug-in-eth.webp)
 
 3\. Gently slide R-PRO-1 into the Ceiling Mount.
 
-![](/assets/r-pro-1-ceiling-mount-insert-r-pro-1.jpg)
+![](/assets/r-pro-1-ceiling-mount-insert-r-pro-1.webp)
 
 4\. Push the R-PRO-1 back 1inch (around 2.5cm) to make sure the lip of the cover fits over the Ceiling Mount.
 
-![](/assets/r-pro-1-ceiling-mount-recess-r-pro-1.jpg)
+![](/assets/r-pro-1-ceiling-mount-recess-r-pro-1.webp)
 
 5\. Gently press the ceiling mount cover until it is securely attached to the Ceiling Mount.
 
-![](/assets/r-pro-1-ceiling-mount-replace-cover.jpg)
+![](/assets/r-pro-1-ceiling-mount-replace-cover.webp)
 
 &nbsp;

docs/products/rpro1/troubleshooting/rpro1-boot-mode.md

@@ -12,11 +12,11 @@ description: Step by step guide for putting The R-PRO-1 In Boot Mode.
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently remove the PCB from the case and flip it over.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Locate the boot button on the bottom right side of the PCB.
 
@@ -30,11 +30,11 @@ description: Step by step guide for putting The R-PRO-1 In Boot Mode.
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently remove the PCB from the case and flip it over.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Locate the boot button on the bottom right side of the PCB.
 

docs/products/rpro1/troubleshooting/rpro1-teardown.md

@@ -8,11 +8,11 @@ description: Step by step guide for tearing down your R-PRO-1 to replace parts,
 
 1\. Unplug your R-PRO-1 from power and remove the back.
 
-![](/assets/rpro-1-add-co2-lift-lid-1.jpg)![](/assets/rpro-1-add-co2-remove-lid.jpg)
+![](/assets/rpro-1-add-co2-lift-lid-1.webp)![](/assets/rpro-1-add-co2-remove-lid.webp)
 
 2\. Gently remove the PCB from the case and flip it over.
 
-![](/assets/r-pro-1-no-case-mmwave-facing-up.jpg)
+![](/assets/r-pro-1-no-case-mmwave-facing-up.webp)
 
 3\. Gently remove the LD2412 as shown below.